未分類 蝸輪減速機一般故障原因及改善方法 Posts by : Shinwe | 2018-05-04 蝸輪減速機一般故障原因及改善方法 SOLUTIONS AND REASONS FOR THE GENRAL FAULTS OF REDRCTION GEARS 故障情形 FAULT DESCRIPTION 故障原因 REASONS 解決方法 SOLUTIONS 減速機過熱 Overheating *超負荷運轉 *潤滑油過少或過多 *潤滑油不良或不適當 *油封過度磨擦 *出力軸與傳動裝置連接不當 *Overloading. *Insufficient or excess lubricant oil. *Inferior or improper lubricant oil. *Oil seal is over-rubbed. *Improper connection between output shaft and transmitting device. *調整至適當負荷 *依指示加入適量潤滑油 *油排出後加入適當潤滑油 *在油封處滴數滴潤滑油 *調整至適當位置 *Adjust to proper loading. *Fill in adequate lubricant oil as indication. *Fill in proper lubricant oil after draining out oil. *Drop lubricant on oil seal. *Adjust to proper position. 減速機雜音 Noise *蝸輪、蝸桿嚙合不良 *軸承損傷或間隙過大 *潤滑油不足 *異物侵入 *Poor fit between worm wheel and worm shaft. *Bearing damaged or clearance too large. *Insufficient lubricant oil. *Invaded by foreign objects. *修整齒接觸面(請與本公司聯絡) *更換軸承 *依指示加入適量潤滑油 *去除異物並更換潤滑油 *Finish contact surfaces of gears(please contact with us) *Replace bearing. *Fill in proper adequate lubricant oil as indication. *Remove foreign objects and replace lubricant oil. 不正常振動 Abnormal vibration *傳動裝置固定不良 *蝸輪磨耗或損傷 *軸承磨耗或損傷 *螺栓鬆脫 *異物侵入 *Transmitting device is not fixed. *Worm wheel worn or damaged. *Bearing worn or damaged. *Bolt loosed. *Invaded by foreign objects. *將傳動裝置固定 *更換蝸輪(請與本公司連絡) *更換軸承 *鎖緊螺栓 *去除異物並更換潤滑油 *Fix transmitting device. *Replace worm wheel(please contact with us) *Replace bearing. *Tighten bolt. *Remove foreign objects and replace lubricant oil. 漏油 Oil leakage *油封損傷 *迫緊閉(GASDET)破損 *油量過多 *洩油栓鬆脫 *油鏡破損 *Oil seal damaged. *Gasket damaged. *Excess oil. *Oil drain plug loosed. *Oil gauge damaged. *更換油封 *更換迫緊 *依指示加入適量潤滑油 *鎖緊洩油栓 *更換油鏡 *Replace oil seal. *Replace gasket. *Fill in adequate lubricant oil as indication. *Tighten oil drain plug. *Replace oil gauge. 入力或出力軸不轉 Input or output shaft can’t rotate *蝸輪蝸桿過熱膨脹 *軸承損傷 *異物嵌入 *蝸輪、蝸桿過度磨損 *Worm wheel and worm shaft expanded by overheating. *Bearing damaged. *Invaded by foreign objects. *Excess wear of worm wheel and worm shaft. *更換蝸輪或蝸桿(請與本公司連絡) *更換軸承 *取出異物並更換潤滑油 *更換蝸輪或蝸桿(請與本公司連絡) *Replace worm wheel or worm shaft(please contact with us) *Replace bearing. *Remove foreign objects and replace lubricant oil. *Replace worm wheel or worm shaft(please contact with us). 蝸輪過度磨耗 Worm wheel over-worn *超負荷 *潤滑油不良或不適當 *潤滑油不足 *軸承磨損 *運轉溫度過高 *Worm wheel and worm shaft expanded by overheating. *Inferior or improper lubricant oil. *Bearing damaged. *Operating temperature too high. *調整至適當負荷 *更換適當潤滑油 *依指示加入適量潤滑油 *更換軸承 *改善通風環境 *Adjust to proper loading. *Replace proper lubricant oil. *Fill in adequate lubricant oil as indication. *Replace bearing. *Improve ventilation conditions. *以上所列為一般故障原因,如有其它故障情形時,請與本公司連絡,我們將會提供最正確之服務。 Tags: Share this post